Loading..

Product was successfully added to your shopping cart.

Sublimation Shin Pads & Accessories

Sublimation Shin Pads & Accessories

  • Sublimation Shin Pads & Accessories - Sublimation example
  • Shin Pads - Sublimated sleeves
  • Sublimation Shin Pads - Back with silicon pad
  • Pair of Sublimation Shin Pad Sleeves
  • Sublimation Shin Pads - Inside the sleeves
  • Sublimation Shin Pads & Accessories - Adhesive pad on the back
  • Sublimation Moulds for shin pads - Top view
  • Sublimation Moulds for shin pads - Bottom view

Sublimation Shin Pads & Accessories

Unisex shin pads, you can personalise using 3D sublimation. You can also buy sleeves and the moulds to sublimate them.

  • Made of rigid white plastic with gloss finish.
  • Sale unit: Pair (left/right).
  • Print area (per shin pad): 10 x 14 cm (kids) - 11.5 x 17 cm (adults) - 12.5 x 19 cm (XXL).

More information about shin pads and their accessories.

How to sublimate the shin pads and their sleeves?

+ Read More
- Read Less
Availability: Shown on each product
  • Immediate:

Product Name Price Availability Qty
Pair of Sublimation Shin Pads for kids
Pair of Sublimation Shin Pads for kids
Ref. 038763
€12.90
  • 10 for €10.75 each
  • 100 for €9.99 each
  • 500 for €9.37 each
  • Immediate: 0 units
Pair of Sublimation Shin Pads for adults
Pair of Sublimation Shin Pads for adults
Ref. 038762
€12.90
  • 10 for €10.75 each
  • 100 for €9.99 each
  • 500 for €9.37 each
  • Immediate: 0 units
Pair of Sublimation Shin Pads - XXL
Pair of Sublimation Shin Pads - XXL
Ref. 039396
€12.90
  • 10 for €10.75 each
  • 100 for €9.99 each
  • 500 for €9.37 each
  • Immediate: 0 units
Pair of Sublimation Shin Pad Sleeves
Pair of Sublimation Shin Pad Sleeves
Ref. 038764
€3.95
  • 10 for €3.69 each
  • 100 for €3.35 each
  • 1000 for €3.15 each
  • Immediate: 0 units
Sublimation Moulds for shin pads
Sublimation Moulds for shin pads
Ref. 038765
€89.00
  • Immediate: 1 units
VAT not included
Get free € to redeem on your next order by buying these products. Discover the Brildor Loyalty Program

Brildor Club is a direct discount program for your purchases. Whenever you place an order (minimum purchase of €10), some discount balance will be generated into your customer account for you to use on your next purchase. The more you buy, the more you save.
You will get access to the Brildor Club as soon as you register as a new customer, and will receive a €5 welcome balance.

 

How do I get some discount balance?


As a Regular Brildor Member:

  • On orders up to €180, you may receive €0.20 for every €10 you spend
  • On orders over €180, you may receive €0.30 for every €10 you spend
  • We will give you an extra €10 if you make 10 purchases over €100


As a Premium Brildor Member:

If you are a Premium Member of the Brildor Club, you will accumulate 25% more balance, so you can obtain:

  • On orders up to €180, you may receive €0.25 for every €10 you spend
  • On orders over €180, you may receive €0.375 for every €10 you spend

  

Who are Premium Brildor Members?


If over the last 12 months your purchases have exceeded €3,000, you will automatically be upgraded to the Premium Brildor Member category. This amount is checked daily. As soon as you reach it, you will become a Premium Member the day after.

 

Terms and conditions of the Brildor Club

  • Loyalty balance will be added when placing an order with an immediate payment method (Credit/debit card, Paypal and Pagantis).
  • Your balance will show in the "Your credit" section inside "Your account", and you can use it by selecting "Payment methods".
  • You can use your balance without needing to have a minimum accumulated amount or reach a minimum order value. Nonetheless, you won't be able to get a higher discount than your order value.
  • Balance expires after 6 months without making any purchase.
  • The balance is calculated on the net amount of the purchase: excluding taxes, shipping, coupons, and promotional discounts.
  • The cancellation of an order implies the loss of the balance generated in that purchase.
  • On a full-order return, the amount to be refunded will be the amount paid by the customer.
  • If the return of the order is due to causes beyond the control of Brildor, the redeemed balance won't be restored. However, the balance generated with this purchase won't be removed.
Sublimation Shin Pads & Accessories Description

More information about shin pads for sublimation and their accessories

  • They are perfect for any sports practice where you would need to protect your lower legs such as football, hockey, rollerblading, skateboarding, cycling or combat sports...
  • Unisex, they are available for kids and adults.
  • Customisable on their outer face.
  • Can only be sublimated using a 3D vacuum heat press. This is a machine for heat transfers that creates a vacuum.
  • Reverse made of black EVA foam. It makes the shin pads pleasant to wear and reduces impact from shock, providing even better leg protection.

TEMPLATES AVAILABLE IN DIFFERENT FILE FORMATS

SHIN PAD SLEEVES

  • Shin pad sleeves with a front opening to insert the shin pad and another one to place the leg in.
  • Made of elastic white polyester fabric. Perforated for better breathability.
  • Customisable on both sides with a heat press.
  • One size fits all. Suitable for kids and adults.
  • Not left or right leg specific for easy wearing.
  • Sale unit: pair of sleeves.

MOULDS

  • Specially manufactured to sublimate shin pads both for kids and adults.
  • Coated with an aluminium layer.
  • Highly pressure resistant.
  • Sale unit: pair of moulds - right/left.

DIMENSIONS (APPROX.)

Reference nº
Name Dimensions Print area

038763

Shin pad (kids) 8 cm x 14.3 cm x 2 mm 10 x 14.3 cm
Silicone foam (kids)
9.3 cm x 13.8 cm x 4 mm
038762 Shin pad (adults) 8.5 cm x 17 cm x 2 mm 11.5 x 17 cm
Silicone foam (adults) 10.5 cm x 15.5 cm x 4 mm
039396 Shin pad (XXL)
9 cm x 19.5 cm x 2 mm 12.5 x 19 cm
Silicone foam (XXL) 11.5 cm x 18.5 cm x 5 mm
038764 Shin pad sleeve
11.5 x 23 cm 11.5 x 23 cm
038765 Shin pad mould
12 x 19 x 4.8 cm ----

Recommended instructions and parameters for sublimation printing

HOW TO SUBLIMATE SHIN PADS WITH A 3D VACUUM?

  • Preheat the 3D vacuum press with the moulds inside to 200º C and create a vacuum for 10 minutes.
  • Print the design in mirror image and trim it around the image.
  • Place the paper's printed side against each mould and fix it with Heat Resistant Tape.
  • Once preheating time is finished, set it to 200º C for 7-8 minutes.
  • Using protective gloves, place the shin pads on each mould and create a vacuum.
  • Remove the wrinkles that may have formed under vacuum. For that, press with your fingers from the inside out until they are completely gone.
  • Close the press and start the process.
  • At the end of the process, open the press and remove the membrane.
  • Without taking them out, neither from the press nor the moulds, press on the shin pads for 30 seconds to make sure they do not lose their shape.
  • Remove the shin pads from the press, holding them at the ends to prevent any deformation.
  • As they start cooling down, remove the paper from the shin pads.
  • Once completely cool, place the self-adhesive EVA foam on each shin pad. For that, you only need to peel off the protecting paper from the adhesive and fix it on the back of the shin pad. Press on it for a few minutes until the adhesive takes full effect.
  • The shin pads are now ready to use.

HOW TO SUBLIMATE THE SHIN PAD SLEEVES?

  • Print the design in mirror image.
  • Preheat the press to 180ºC - 200ºC.
  • Place the sleeve on the press' lower plate and the paper's printed side against it. Fix the paper with Heat Resistant Tape.
  • Close the press at medium pressure for approximately 40 - 45 seconds.
  • Using a protective glove, remove the newly printed shin pad sleeve.
  • Remove the paper carefully.

Additional Information
Reference nº 926 145
Dimensions (mm) 80 x 143 (Ref. 038763) - 85 x 170 cm (Ref. 038762) - 90 x 195 cm (Ref. 039396)
Print area (mm) 100 x 143 (Ref. 038763) - 115 x 170 cm (Ref. 038762) - 125 x 190 cm (Ref. 039396)
Thickness (mm) 2
Colour White
Surface material Plastic
Items Sport items
Marking techniques 3D Sublimation
Post your question

Questions and Answers

There are no entries.

Sublimation Shin Pads & Accessories Description

More information about shin pads for sublimation and their accessories

  • They are perfect for any sports practice where you would need to protect your lower legs such as football, hockey, rollerblading, skateboarding, cycling or combat sports...
  • Unisex, they are available for kids and adults.
  • Customisable on their outer face.
  • Can only be sublimated using a 3D vacuum heat press. This is a machine for heat transfers that creates a vacuum.
  • Reverse made of black EVA foam. It makes the shin pads pleasant to wear and reduces impact from shock, providing even better leg protection.

TEMPLATES AVAILABLE IN DIFFERENT FILE FORMATS

SHIN PAD SLEEVES

  • Shin pad sleeves with a front opening to insert the shin pad and another one to place the leg in.
  • Made of elastic white polyester fabric. Perforated for better breathability.
  • Customisable on both sides with a heat press.
  • One size fits all. Suitable for kids and adults.
  • Not left or right leg specific for easy wearing.
  • Sale unit: pair of sleeves.

MOULDS

  • Specially manufactured to sublimate shin pads both for kids and adults.
  • Coated with an aluminium layer.
  • Highly pressure resistant.
  • Sale unit: pair of moulds - right/left.

DIMENSIONS (APPROX.)

Reference nº
Name Dimensions Print area

038763

Shin pad (kids) 8 cm x 14.3 cm x 2 mm 10 x 14.3 cm
Silicone foam (kids)
9.3 cm x 13.8 cm x 4 mm
038762 Shin pad (adults) 8.5 cm x 17 cm x 2 mm 11.5 x 17 cm
Silicone foam (adults) 10.5 cm x 15.5 cm x 4 mm
039396 Shin pad (XXL)
9 cm x 19.5 cm x 2 mm 12.5 x 19 cm
Silicone foam (XXL) 11.5 cm x 18.5 cm x 5 mm
038764 Shin pad sleeve
11.5 x 23 cm 11.5 x 23 cm
038765 Shin pad mould
12 x 19 x 4.8 cm ----

Recommended instructions and parameters for sublimation printing

HOW TO SUBLIMATE SHIN PADS WITH A 3D VACUUM?

  • Preheat the 3D vacuum press with the moulds inside to 200º C and create a vacuum for 10 minutes.
  • Print the design in mirror image and trim it around the image.
  • Place the paper's printed side against each mould and fix it with Heat Resistant Tape.
  • Once preheating time is finished, set it to 200º C for 7-8 minutes.
  • Using protective gloves, place the shin pads on each mould and create a vacuum.
  • Remove the wrinkles that may have formed under vacuum. For that, press with your fingers from the inside out until they are completely gone.
  • Close the press and start the process.
  • At the end of the process, open the press and remove the membrane.
  • Without taking them out, neither from the press nor the moulds, press on the shin pads for 30 seconds to make sure they do not lose their shape.
  • Remove the shin pads from the press, holding them at the ends to prevent any deformation.
  • As they start cooling down, remove the paper from the shin pads.
  • Once completely cool, place the self-adhesive EVA foam on each shin pad. For that, you only need to peel off the protecting paper from the adhesive and fix it on the back of the shin pad. Press on it for a few minutes until the adhesive takes full effect.
  • The shin pads are now ready to use.

HOW TO SUBLIMATE THE SHIN PAD SLEEVES?

  • Print the design in mirror image.
  • Preheat the press to 180ºC - 200ºC.
  • Place the sleeve on the press' lower plate and the paper's printed side against it. Fix the paper with Heat Resistant Tape.
  • Close the press at medium pressure for approximately 40 - 45 seconds.
  • Using a protective glove, remove the newly printed shin pad sleeve.
  • Remove the paper carefully.

Additional Information

Reference nº 926 145
Dimensions (mm) 80 x 143 (Ref. 038763) - 85 x 170 cm (Ref. 038762) - 90 x 195 cm (Ref. 039396)
Print area (mm) 100 x 143 (Ref. 038763) - 115 x 170 cm (Ref. 038762) - 125 x 190 cm (Ref. 039396)
Thickness (mm) 2
Colour White
Surface material Plastic
Items Sport items
Marking techniques 3D Sublimation
Post your question

Questions and Answers

There are no entries.

The legal stuff about cookies:


This message requires us to tell you about ourcookie policy.

If you continue browsing, we'll assume you accept it and think it's okay.

Don't worry, this message only comes up once.