LASERFLEX is a water-based PU (polyurethane) film for transferring your designs on fabrics without water-repellent impregnation.
The vinyl is cut as an engraving and therefore does not need to be weeded
The image resolution should be at 500-600 dpi
Made in France by Sef Laval
THINGS TO KEEP IN MIND
The cutting configuration of the laser machine will depend on each model. For this reason, we recommend carrying out preliminary tests to establish the appropriate parameters
The vinyl will leave a dust residue on the machine after cutting. It is advisable to clean this residue when you have finished cutting the vinyl
CUTTING INSTRUCTIONS
Place a 3 mm wooden board on the laser machine to avoid reflections from the work bed
Place the vinyl on the wooden board with the liner side down
Fix the vinyl to the wooden board using adhesive tape so that it does not move due to the compressed air from the machine
Go to Maintain then press Release Motors to adjust the height of the laser head so that it is correctly focused
Load the image and place it in the correct position
In the document settings, adjust the resolution between 500-600 dpi
Now go to the Layer panel and set the cutting speed and cutting power
Start cutting
For the Flux Beamo we have used the following settings:
Print resolution: 500 dpi
Power: 21%
Speed: 110 mm/s
TRANSFER PARAMETERS
Knife blade: 45º
Temperature: 165ºC
Time: 17 seconds
Pressure: 2.5 - 3.0 bar [medium pressure]
APPLICATION INSTRUCTIONS
Wipe off any dust from the vinyl with a dry cloth
Trim off the excess white edges of the vinyl
Preheat the press to 160ºC
Place the garment on the press and pre-press for 4-5 seconds to remove wrinkles and moisture from the fabric
Position the vinyl over the garment and cover with protective paper
Press for 17 seconds, medium pressure
Cool peel the liner
Place the protective paper over the vinyl and press again for 5 seconds with the same parameters
https://www.brildor.com/en/laser-cut-heat-transfer-film-sef-laval-laserflex21808Laser Cut Heat Transfer Film - Sef Laval LaserFlex<p><a name="know-more"></a></p>
<p><strong>INDEX</strong></p>
<p><a href="#know-more1">Description</a></p>
<p><a href="#know-more2">Things to keep in mind</a></p>
<p><a href="#know-more3">Cutting instructions</a></p>
<p><a href="#know-more4">Transfer parameters</a></p>
<p><a href="#know-more5">Application instructions</a></p>
<p><a href="#know-more6">Wash resistance</a></p>
<p><a href="#know-more8">Colour card and data sheet</a></p>
<p> </p>
<p><a name="know-more1"></a></p>
<p><strong>DESCRIPTION</strong></p>
<p>LASERFLEX is a <strong>water-based PU</strong> (polyurethane) <strong>film</strong> for transferring your designs on fabrics without water-repellent impregnation.</p>
<ul>
<li>The vinyl is cut as an engraving and therefore does not need to be weeded</li>
<li>The image resolution should be at <span class="azul-negrita">500-600 dpi</span></li>
<li>Made in France by Sef Laval</li>
</ul>
<p> </p>
<p><a name="know-more2"></a></p>
<p><strong>THINGS TO KEEP IN MIND</strong></p>
<ul>
<li>The cutting configuration of the laser machine will depend on each model. For this reason, we recommend carrying out preliminary tests to establish the appropriate parameters</li>
<li>The vinyl will leave a dust residue on the machine after cutting. It is advisable to clean this residue when you have finished cutting the vinyl</li>
</ul>
<p> </p>
<p><a name="know-more3"></a></p>
<p><strong>CUTTING INSTRUCTIONS</strong></p>
<ul>
<li>Place a 3 mm wooden board on the laser machine to avoid reflections from the work bed</li>
<li>Place the vinyl on the wooden board with the liner side down</li>
<li>Fix the vinyl to the wooden board using adhesive tape so that it does not move due to the compressed air from the machine</li>
<li>Go to Maintain then press Release Motors to adjust the height of the laser head so that it is correctly focused</li>
<li>Load the image and place it in the correct position</li>
<li>In the document settings, adjust the resolution between <span class="azul-negrita">500-600 dpi</span></li>
<li>Now go to the Layer panel and set the cutting speed and cutting power</li>
<li>Start cutting</li>
</ul>
<p><strong>For the Flux Beamo we have used the following settings:</strong></p>
<ul>
<li>Print resolution: <span class="azul-negrita">500 dpi</span></li>
<li>Power: <span class="azul-negrita">21%</span></li>
<li>Speed: <span class="azul-negrita">110 mm/s</span></li>
</ul>
<p> </p>
<p><a name="know-more4"></a></p>
<p><strong>TRANSFER PARAMETERS<br></strong></p>
<ul>
<li>Knife blade: <span class="azul-negrita">45º</span></li>
<li>Temperature: <span class="azul-negrita">165ºC</span></li>
<li>Time: <span class="azul-negrita">17 seconds</span></li>
<li>Pressure: <span class="azul-negrita">2.5 - 3.0 bar</span> [medium pressure]</li>
</ul>
<p> </p>
<p><a name="know-more5"></a></p>
<p><strong>APPLICATION INSTRUCTIONS<br></strong></p>
<ul>
<li>Wipe off any dust from the vinyl with a dry cloth</li>
<li>Trim off the excess white edges of the vinyl</li>
<li>Preheat the press to <span class="azul-negrita">160ºC</span></li>
<li>Place the garment on the press and pre-press for <span class="azul-negrita">4-5 seconds</span> to remove wrinkles and moisture from the fabric</li>
<li>Position the vinyl over the garment and cover with protective paper</li>
<li>Press for <span class="azul-negrita">17 seconds</span>, medium pressure</li>
<li><strong>Cool peel</strong> the liner</li>
<li>Place the protective paper over the vinyl and press again for <span class="azul-negrita">5 seconds</span> with the same parameters</li>
</ul>
<p> </p>
<p><a name="know-more6"></a></p>
<p><strong>WASH RESISTANCE</strong></p>
<ul>
<li>Washing resistance: <span class="azul-negrita">60ºC</span> max</li>
</ul>
<p> </p>
<p><a name="know-more8"></a></p>
<p><strong>COLOUR CARD AND DATA SHEET</strong></p>
<p><a title="LaserFlex colour card and data sheet" href="https://www.brildor.com/media/upload/descargas/Ficha_Tecnica_Vinilo_LaserFlex_Sef_Laval.pdf" target="_blank" rel="nofollow noopener">LaserFlex colour card and data sheet (pdf - 0.45 MB)</a></p>https://www.brildor.com/media/catalog/product/v/i/vinilo-textil-corte-laser-laserflex.jpg2.39instock02.39000https://www.brildor.com/media/catalog/product/v/i/vinilo-textil-corte-laser-laserflex.jpg/Vinyl/Vinyl/Heat Transfer Vinyl/Laser/Laser/Materiales para Corte y Grabado2021-07-24T06:06:04+0000
